Your Complete Tutorial for Bathtub Installation

Website

This article which follows about Tools You Need to Install a New Bathtub is quite engaging. Give it a go and draw your own ideas.

Installing a bathtub isn't specifically rocket science, but it does need solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard job. If the old tub is conveniently obtainable, the project can move easily; if you have to open a wall to get rid of the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require an assistant to move out the old tub as well as set in the new one. See to it you have qualified yourself for the task as well as are comfortable trying it. As opposed to hiring a service provider to take control of a halfway-completed task, it is much better to consider utilizing one before you begin. Possibilities are you might need a professional plumber to make tube connections.
This write-up will certainly aid you set up a brand-new tub in your bathroom if you have currently bought a new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your tools and product checklist need to consist of the following:

New Bath tub

Hammer

Pipeline Wrenches

Prybar

Shatterproof glass

Level

Pliers

Adjustable Wrench

Putty Blade

Screwdriver

Cold Blade

Measuring tape

Pipeline Caps

Getting ready for the Setup

First of all, the sustaining framework supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent pressure on the bathtub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its final position.

Removing Old Taps

If you need to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome due to the restricted accessibility that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Prior to going on to fit the new faucets, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.

Setting up the Bath tub

Utilizing both wood boards under its feet, position the bathtub in the called for position. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the bath tub up until the level reviews level.
To mount faucets, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and examine all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the bathtub and likewise inspect the overflow electrical outlet and also the regular outlet for leaks.
Ultimately, fix the bathroom paneling as defined in the supplier's instruction manual. Tiling and also securing around the bath tub needs to wait until the tub has actually been used at least when as this will certainly settle it right into its last setting.

Fitting New Taps

If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in location in between the tap as well as the sink. Secure the faucet in position with the manufacturer provided backnut. Once the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be attached to the tap finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.

Tiling Around the Bathtub

In the area where the bath meets the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split a rigid seal, causing the water to permeate the wall surface between the bathroom and also the tiling, leading to problems with moisture and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures and fittings. They are sold in tubes and cartridges, and also can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always load the bathtub with water before securing, to allow for the movement experienced when the bathtub is in usage. The sealant can crack rather very early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the marketplace. It is advisable to fit the tiles making use of water-resistant or water-proof adhesive and grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I found that review about Installing A Bathtub when doing a lookup on the search engines. Sharing is caring. You just don't know, you could be helping someone out. I am grateful for your time. Come back soon.

Recurring Service Plans